Citations

Background Long surgical procedures with loupe magnification and microscopes may put microsurgeons at an increased risk of musculoskeletal discomfort. Identifying the prevalence and impact of work-related musculoskeletal discomfort may guide preventive strategies to prolong well-being, job satisfaction, and career duration. Methods An online 29-question survey was designed to evaluate work-related musculoskeletal discomfort. The survey was created and distributed electronically through a private survey research center and was sent to the members of the American Society for Reconstructive Microsurgery. Results There were 117 respondents (16.7% response rate): 80% were men; 69% were aged 31 to 50 years; and 68% were in academic practice. On a scale of 0 to 10 (0, no pain and 10, worst pain), the median for work-related musculoskeletal discomfort for surgery without loupes or microscope was 2; with loupes, 4; and with a microscope, 5. Pain was most common in the neck. Half of the surgeons reported pain within 4 hours of surgery, and 57% feared that pain would influence future surgical performance. Surgeon discomfort affected posture (72%), stamina (36%), sleep (29%), relationships (25%), concentration (22%), and surgical speed (19%). Tremor caused by the discomfort occurred in 8%. Medical treatment for discomfort was sought by 29%. Time off work for treatment occurred for 8%. Conclusion Work-related musculoskeletal discomfort can affect many aspects of a microsurgeon's life and has the potential to limit a surgeon's ability to operate. Therefore, more emphasis is needed in the surgical community on the important issues of occupational health and surgical ergonomics for microsurgeons.

AbstractBackgroundOvercoming β-lactam resistance in pathogens such as Pseudomonas aeruginosa is a major clinical challenge. Rapid molecular diagnostics (RMDs) have the potential to inform selection of empiric therapy in patients infected by P. aeruginosa.MethodsIn this study, we used a heterogeneous collection of 197 P. aeruginosa that included multidrug-resistant isolates to determine whether 2 representative RMDs (Acuitas Resistome test and VERIGENE gram-negative blood culture test) could identify susceptibility to 2 newer β-lactam/β-lactamase inhibitor (BL-BLI) combinations, ceftazidime/avibactam (CZA) and ceftolozane/tazobactam (TOL/TAZO).ResultsWe found that the studied RMD platforms were able to correctly identify BL-BLI susceptibility (susceptibility sensitivity, 100%; 95% confidence interval [CI], 97%, 100%) for both BLs-BLIs. However, their ability to detect resistance to these BLs-BLIs was lower (resistance sensitivity, 66%; 95% CI, 52%, 78% for TOL/TAZO and 33%; 95% CI, 20%, 49% for CZA).ConclusionsThe diagnostic platforms studied showed the most potential in scenarios where a resistance gene was detected or in scenarios where a resistance gene was not detected and the prevalence of resistance to TOL/TAZO or CZA is known to be low. Clinicians need to be mindful of the benefits and risks that result from empiric treatment decisions that are based on resistance gene detection in P. aeruginosa, acknowledging that such decisions are impacted by the prevalence of resistance, which varies temporally and geographically.

Abstract The objective of this study is to compare the cyclic loading strength and ultimate failure load in suture anchor repair versus transosseous tunnel repair of patellar tendons using a cadaver model. Twelve cadaveric patella specimens were used (six matched pairs). Dual-energy X-ray absorptiometry (DXA) measurements were performed to ensure equal bone quality among groups. All right knees were assigned to the suture anchor repair group (n = 6), whereas all left knees were assigned to the transosseous bone tunnel group (n = 6). Suture type and repair configuration were equivalent. After the respective procedures were performed, each patella was mounted into a gripping jig. Tensile load was applied at a rate of 1 Hz between magnitudes of 50 and 150 N, 50 and 200 N, 50 and 250 N, and tensile load at a rate of 0.1 mm/s until failure. Failure was defined as a sharp deviation in the linear load versus displacement curve, and failure mode was recorded. DXA measurements demonstrated equivalence of bone quality between the two groups (p > 0.05). During cyclic load testing, there was only a statistically significant difference between the groups with regard to cyclic loading at the 50 to 200 N loading cycle (p = 0.010). There was no statistically significant difference between the groups with regard to ultimate load to failure (p = 0.43). Failure mode within the suture anchor cohort occurred through anchor pullout except for one, which failed through the tendon. All specimens within the transosseous cohort failed through the midsubstance of the tendon except for one, which failed through suture breakage. Suture anchor repair demonstrated a similar biomechanical profile regarding cyclic loading and ultimate load to failure when compared with “gold standard” transosseous tunnel patellar tendon repair with a trend toward less gapping in the suture anchor group. Using suture anchors for repair of the patella tendon has similar biomechanical properties to transpatellar tunnels but may provide other clinical advantages.