Moroder, Philipp

Background: Irreparable posterosuperior rotator cuff (PSRC) tears have been shown to result in shoulder pain and loss of function. Purpose/Hypothesis: The purpose of this study was to determine the effect of the loss of active or passive function of the PSRC on compensatory muscle loads in the deltoid and the remaining rotator cuff. It was hypothesized that both deactivation and resection of the PSRC would result in load increases in the remaining muscles and that resection of the PSRC would result in even higher required compensatory forces than would mere deactivation. Study Design: Controlled laboratory study. Methods: A total of 7 cadaveric shoulders were tested using a biomechanical shoulder simulator with 10 independently controlled actuators for various muscles (anterior, middle, and posterior deltoid; inferior and superior subscapularis; latissimus dorsi; pectoralis major; teres minor; supraspinatus; and infraspinatus) and 3-dimensional motion tracking. The muscle loads representing the latissimus dorsi and pectoralis major were each held constant, and the remaining muscle actuator forces required to abduct the arm in the scapular plane were determined. The actuator forces corresponding with arm elevation from 20° to 65° were compared at 5° increments for 3 testing conditions: (1) intact, active PSRC; (2) intact, deactivated PSRC; and (3) resected PSRC and shoulder capsule. Results: In both the deactivated and resected states, the teres minor showed a significant increase in required muscle forces through nearly the entire tested range of arm elevation compared to the active state. This was also the case for the subscapularis but only at higher elevation angles. The deltoid demonstrated increased muscle forces of at least 1 of its subunits between 25° and 55° of elevation when comparing the deactivated state or resected state to the active state. However, through nearly the entire range of elevation, no statistically significant differences were found between the deactivated and resected states for any of the actuator loads representing muscle forces. Conclusion: The loss of active function of the PSRC led to compensatory loads on the remaining rotator cuff and deltoid, regardless of the passive presence of the PSRC as a supposed subacromial spacer. Clinical Relevance: The findings encourage the exploration of treatment procedures that mimic the active function of the PSRC when the rotator cuff itself is irreparable.

ObjectivesThe bony shoulder stability ratio (BSSR) allows for quantification of the bony stabilisers in vivo. We aimed to biomechanically validate the BSSR, determine whether joint incongruence affects the stability ratio (SR) of a shoulder model, and determine the correct parameters (glenoid concavity versus humeral head radius) for calculation of the BSSR in vivo.MethodsFour polyethylene balls (radii: 19.1 mm to 38.1 mm) were used to mould four fitting sockets in four different depths (3.2 mm to 19.1mm). The SR was measured in biomechanical congruent and incongruent experimental series. The experimental SR of a congruent system was compared with the calculated SR based on the BSSR approach. Differences in SR between congruent and incongruent experimental conditions were quantified. Finally, the experimental SR was compared with either calculated SR based on the socket concavity or plastic ball radius.ResultsThe experimental SR is comparable with the calculated SR (mean difference 10%, sd 8%; relative values). The experimental incongruence study observed almost no differences (2%, sd 2%). The calculated SR on the basis of the socket concavity radius is superior in predicting the experimental SR (mean difference 10%, sd 9%) compared with the calculated SR based on the plastic ball radius (mean difference 42%, sd 55%).ConclusionThe present biomechanical investigation confirmed the validity of the BSSR. Incongruence has no significant effect on the SR of a shoulder model. In the event of an incongruent system, the calculation of the BSSR on the basis of the glenoid concavity radius is recommended. Cite this article: L. Ernstbrunner, J-D. Werthel, T. Hatta, A. R. Thoreson, H. Resch, K-N. An, P. Moroder. Biomechanical analysis of the effect of congruence, depth and radius on the stability ratio of a simplistic ‘ball-and-socket’ joint model. Bone Joint Res 2016;5:453–460. DOI: 10.1302/2046-3758.510.BJR-2016-0078.R1.