Goh, Brian Chun Kim

Study Design Retrospective Cohort Study. Objectives To determine if 3D printed porous titanium (Ti) cages compared to non-porous polyetheretherketone (PEEK) cages predicted improved fusion rate or clinical outcomes after transforaminal lumbar interbody fusion (TLIF). Methods All adult patients who underwent one- and two-level TLIF for degenerative conditions by a single surgeon at an academic center between 2017-2021 were retrospectively identified. Patients were dichotomized into porous Ti and non-porous PEEK interbody cage groups. Fusion status was assessed by at 6-months and 1-year postoperatively by CT Bridwell scale and flexion/extension X-Rays. Postoperative complications (CT-based subsidence, adjacent segment disease, reoperation rates) and interval changes in lumbar radiographic alignment at short- and long-term follow-up were determined. Univariate and multivariate analysis compared patient and surgical factors, fusion rates, alignment, and complications across interbody groups. Results A total of 136 patients with 169 unique fusion levels (125 Ti cages, 44 PEEK cages) met the inclusion/exclusion criteria. Ti relative to PEEK interbodies had significantly decreased surface area and increased height and lordosis. Ti cage use was associated with greater subsidence ( P < 0.001) but did not independently predict maximum subsidence on regression ( P = 0.109). In the overall cohort, there were no significant differences in fusion rates or lumbopelvic alignment between interbody groups. Reoperation (Ti: 10.9% vs PEEK: 28.6%, P = 0.026) and reoperation for pseudoarthrosis (Ti: 2.0% vs PEEK: 11.4%, P = 0.038) was significantly more likely in the PEEK relative to the Ti group. Conclusions Use of 3D printed porous Ti cages relative to non-porous PEEK cages may mitigate pseudoarthrosis related reoperation after TLIF.

Study Design: Retrospective observational study of consecutive patients Objective: The purpose of the study was to evaluate VBQ as a predictor of interbody subsidence and to determine threshold values that portend increased risk of subsidence. Summary of Background Data: Many risk factors have been reported for the subsidence of interbody cages in anterior cervical discectomy and fusion (ACDF). MRI Vertebral Bone Quality (VQB) is a relatively new radiographic parameter that can be easily obtained from preoperative MRI and has been shown to correlate with measurements of bone density such as DXA and CT Hounsfield Units. Methods: All patients who underwent 1- to 3-level ACDF using titanium interbodies with anterior plating between the years 2018 and 2020 at our tertiary referral center were included. Subsidence measurements were performed by 2 independent reviewers on CT scans obtained 6 months postoperatively. VBQ was measured on pre-operative sagittal T1 MRI by 2 independent reviewers, and values were averaged. Results: Eight-five fusion levels in 44 patients were included in the study. There were 32 levels (38%) with moderate subsidence and 12 levels with severe subsidence (14%). The average VBQ score in those patients with severe subsidence was significantly higher than those without subsidence (3.80 vs. 2.40, P<0.01). A threshold value of 3.2 was determined to be optimal for predicting subsidence (AUC=0.99) and had a sensitivity of 100% and a specificity of 94.1% in predicting subsidence. Conclusions: VBQ strongly correlates with the subsidence of interbody grafts after ACDF. A threshold VBQ score value of 3.2 has excellent sensitivity and specificity for predicting subsidence. Spine surgeons can use VBQ as a readily available screening tool to identify patients at higher risk for subsidence. Level of Evidence: Level—IV

Study design. Retrospective observational study of consecutive patients. Objective. The purpose of the study is to determine if a surgeon’s qualitative assessment of bone intraoperatively correlates with radiologic parameters of bone strength. Summary of Background Data. Preoperative radiologic assessment of bone can include modalities such as computed tomography (CT) Hounsfield units (HUs), dual-energy x-ray absorptiometry (DXA) bone mineral density with trabecular bone score (TBS) and magnetic resonance imaging vertebral bone quality (VBQ). Quantitative analysis of bone with screw insertional torque and pull-out strength measurement has been performed in cadaveric models and has been correlated to these radiologic parameters. However, these quantitative measurements are not routinely available for use in surgery. Surgeons anecdotally judge bone strength, but the fidelity of the intraoperative judgment has not been investigated. Methods. All adult patients undergoing instrumented posterior thoracolumbar spine fusion by one of seven surgeons at a single center over a 3-month period were included. Surgeons evaluated the strength of bone based on intraoperative feedback and graded each patient’s bone on a 5-point Likert scale. Two independent reviewers measured preoperative CT HUs and magnetic resonance imaging VBQ. Bone mineral density, lowest T-score, and TBS were extracted from DXA within 2 years of surgery. Results. Eighty-nine patients were enrolled and 16, 28, 31, 13, and 1 patients had Likert grade 1 (strongest bone), 2, 3, 4, and 5 (weakest bone), respectively. The surgeon assessment of bone correlated with VBQ (τ=0.15, P=0.07), CT HU (τ=−0.31, P<0.01), lowest DXA T-score (τ=−0.47, P<0.01), and TBS (τ=−0.23, P=0.06). Conclusion. Spine surgeons’ qualitative intraoperative assessment of bone correlates with preoperative radiologic parameters, particularly in posterior thoracolumbar surgeries. This information is valuable to surgeons as this supports the idea that decisions based on feel in surgery have a statistical foundation.