Cornella, Jeffrey L.

Our polyvinyl alcohol feedstock was prepared through carbic anhydride functionalization, UV curing during direct ink writing, and base treatment. The scaffold exhibited mechanical properties similar to pelvic floor tissue.

Abstract 3D printing, also known as additive manufacturing, holds immense potential for rapid prototyping and customized production of functional health‐related devices. With advancements in polymer chemistry and biomedical engineering, polymeric biomaterials have become integral to 3D‐printed biomedical applications. However, there still exists a bottleneck in the compatibility of polymeric biomaterials with different 3D printing methods, as well as intrinsic challenges such as limited printing resolution and rates. Therefore, this review aims to introduce the current state‐of‐the‐art in 3D‐printed functional polymeric health‐related devices. It begins with an overview of the landscape of 3D printing techniques, followed by an examination of commonly used polymeric biomaterials. Subsequently, examples of 3D‐printed biomedical devices are provided and classified into categories such as biosensors, bioactuators, soft robotics, energy storage systems, self‐powered devices, and data science in bioplotting. The emphasis is on exploring the current capabilities of 3D printing in manufacturing polymeric biomaterials into desired geometries that facilitate device functionality and studying the reasons for material choice. Finally, an outlook with challenges and possible improvements in the near future is presented, projecting the contribution of general 3D printing and polymeric biomaterials in the field of healthcare.

AbstractPelvic organ prolapse (POP) is a dysfunction that affects a large proportion of women. Current support scaffolds’ lack of biocompatibility, biodegradability, and mechanical compliance are associated with surgical complications including erosion and pain, indicating the urgent need for new tissue scaffolds with customizable functions. A new material that uses polyvinyl alcohol (PVA) as the main ingredient and is chemically tuned to possess suitable mechanical properties and degradation rates for the surgical treatment of POP is developed. Specifically, the thiol‐norbornene “click” chemistry enables the sol‐gel transition of the biomaterial under UV‐light without side‐products. Meanwhile, NaOH treatment further toughens the hydrogel with a higher crosslink density. The PVA‐based biocompatible ink can be printed with UV‐facilitated direct ink writing due to the rapidly UV‐initiated chemical crosslink; in situ image analysis and machine learning methods are applied during this procedure to quantify and improve the printing quality. The cell viability results demonstrate the biocompatibility of the POP scaffolds, suggesting the potential for future animal studies and the possibility of clinical research. This study bridges polymer chemistry and manufacturing engineering with a specific tissue engineering application to solve the common disorder of POP, shedding light on individualized medicine and intelligent systems for biomedical engineering.

Abstract3D printing (additive manufacturing (AM)) has enormous potential for rapid tooling and mass production due to its design flexibility and significant reduction of the timeline from design to manufacturing. The current state‐of‐the‐art in 3D printing focuses on material manufacturability and engineering applications. However, there still exists the bottleneck of low printing resolution and processing rates, especially when nanomaterials need tailorable orders at different scales. An interesting phenomenon is the preferential alignment of nanoparticles that enhance material properties. Therefore, this review emphasizes the landscape of nanoparticle alignment in the context of 3D printing. Herein, a brief overview of 3D printing is provided, followed by a comprehensive summary of the 3D printing‐enabled nanoparticle alignment in well‐established and in‐house customized 3D printing mechanisms that can lead to selective deposition and preferential orientation of nanoparticles. Subsequently, it is listed that typical applications that utilized the properties of ordered nanoparticles (e.g., structural composites, heat conductors, chemo‐resistive sensors, engineered surfaces, tissue scaffolds, and actuators based on structural and functional property improvement). This review's emphasis is on the particle alignment methodology and the performance of composites incorporating aligned nanoparticles. In the end, significant limitations of current 3D printing techniques are identified together with future perspectives.

Abstract Extrauterine spread of leiomyomas is rare and most commonly occurs in the lungs. We present a case of simultaneous metastatic leiomyomatosis to the lungs and peritoneal cavity following laparoscopic myomectomy with power morcellation. The patient presented to our institution for further management where she underwent a robotically assisted hysterectomy with bilateral salpingo-oophorectomy. Leiomyomatous implants measuring up to 2.4 cm were resected from bowel mesentery and bladder peritoneum. Subsequent serial computed tomography imaging confirmed stable pulmonary nodules without new intraperitoneal lesions. Increasing number of cases involving extrauterine spread of leiomyomas has been reported with the introduction of power morcellation. The exact pathogenesis is unknown but is likely multifactorial. We emphasize that although the incidence of spread of benign disease is low, it is important to recognize this phenomenon as we will likely continue to encounter similar cases in the coming years.

Sacral neuromodulation is a therapeutic option for women with detrusor overactivity and more recently has been used in patients with fecal incontinence and slow-transit constipation. A 47-year-old woman presented with chronic constipation since childhood. She used multiple laxatives, fiber supplements, and enemas, all without success, and defecated only once per week. Extensive investigations, including barium enema, colonoscopy, defecating proctography, pelvic magnetic resonance imaging, and anorectal manometry all were normal. A transit study showed delayed small-bowel emptying. Colonic transit could not be accurately interpreted because of the marked delayed in proximal transit. An ileostomy was being considered to defunction the colon after the patient become desperate for a better quality of life. She also complained of severe urinary frequency and incomplete emptying. A cystoscopy was normal, and a temporary sacral neuromodulation device was inserted as a staged procedure to improve her urinary symptoms. From the day of device placement and thereafter, the patient defecated without difficulty and has also been free of bladder symptoms. Repeat colonic transit has shown normalization of the stomach, small bowel, and colon.